T-Groove®-NR is an interior metal wall panel or an exterior metal wall panel. It can also be used for ceilings, fascia, and soffits. This variation of the metal panel has no reveal between the panel side lap.
Metal Fascia, Soffit, And Wall Panel
Are you looking to make your metal fascia, soffit, or wall panels the focal point of your building? T-Groove® has bold and clean directional sight lines that will look stunning on your house. It’s stronger and easier to install than using flat sheets. When using flats sheets on a job it is a design build application. T-Groove® has an install guide that has solutions for all of your common flashing details. T-Groove® soffits are perfect for roofing systems that aren’t sealed or do not have insulation attached to the attic floor. They are available in a variety of pre-painted non-vented metal soffit panels.
Concealed Fastener Panel
T-Groove®-1.0 is a one inch deep metal wall panel that has concealed fasteners. The “1.0” stands for 1″ reveal which means there’s there’s a 1″ gap between the panel side laps. The reveal gives the panels depth and it looks similar to board and batten panels.
Rib Height: 1″
Overall Coverage: 12″-20″
Standard Face Sizes: 12″, 14″, 16″, 18″, 20″
Custom Face Sizes: 13″, 15″, 17″, 19″
Panel Length: 1′ to 45′ max
Reveal: 1″
Material Type:
T-Groove® Metal Soffit and Flush Wall Panel – NR
Gauge: 22, 24
Fasteners: Concealed
Substrate: AZ50 Minimum (AKA Galvalume®/Zincalume®)
Stiffening Ribs or Pencil Ribs: Available Upon Request
Single or Double Vent Strips: Available Upon Request
Installation: Installation Over A Solid Substrate (Vertical or Horizontal)
Applications: Residential, Commercial, Agricultural, Interior
There are eleven color charts to choose from:
Our standard Polyvinylidene Difluoride (PVDF), has a chemical composition that gives it high mechanical strength and superior abrasion resistance. The tough engineering thermoplastic has increased durability, excellent chemical resistance to halogen and acids that can cause degradation. The surface of PVDF panels is able to handle high temperatures and extensive ultraviolet ray exposure while resisting fading and chalking for longer than SMP painted panels.
By using aluminum roofing and siding panels in PVDF paint, you will have vibrant and attractive painted aluminum panels for longer than any other paint system.
We also offer special ordered colors. These metal roofing colors are not in stock. They are supplied on a job by job basis. If you see a color that you like, there are some things that you should be aware of.
We recommend that you start by looking at all of our standard metal roofing colors. You can find the links below on this page. They cost less and can be manufactured quicker. If you need something different, these colors below might be your solution to finding the perfect metal roofing color for your house.
500 Sq. Ft. Minimum
We also offer special ordered colors. These metal roofing colors are not in stock. They are supplied on a job by job basis. If you see a color that you like, there are some things that you should be aware of.
We recommend that you start by looking at all of our standard metal roofing colors. You can find the links below on this page. They cost less and can be manufactured quicker. If you need something different, these colors below might be your solution to finding the perfect metal roofing color for your house.
Click on a color category below to see all of the colors available:
We also offer special ordered colors. These metal roofing colors are not in stock. They are supplied on a job by job basis. If you see a color that you like, there are some things that you should be aware of.
We recommend that you start by looking at all of our standard metal roofing colors. You can find the links below on this page. They cost less and can be manufactured quicker. If you need something different, these colors below might be your solution to finding the perfect metal roofing color for your house.
About Metal Roofing
How can I use T-Groove Metal Roofing Panels?
Metal Flush Wall Panels
T-Groove® Flush Panels are designed for wall, fascia and soffit applications where a flush or flat appearance is desired. A low profile and concealed fastening system improves the flush appearance while providing additional strength. Available for immediate delivery from our facilities in Ontario, CA. Get a free quote today.
Metal Soffit Panels
The under siding of a roof is just as important as the roof itself. Unfortunately, they often are the most neglected area of the roof. Adding soffit panels to your roofing system can be looked at in two fold – purely for aesthetics and as a first line defense against wind, rain, and pests from entering. T-Groove® soffits are perfect for roofing systems that aren’t sealed or do not have insulation attached to the attic floor. They are available in a variety of pre-painted non-vented metal soffit panels.
What are the features and benefits of metal roofing?
What is the difference between Exposed Fastener Panels vs. Concealed Fastener Panels?
What should I expect when I order from Metal Roofing California?
Excellent customer service is important to us. When you place your order with Western Metal Deck you can expect the following:
